In Texas, non-exempt mold assessors and remediators must be licensed by the Texas Department of Licensing and Regulation under Chapter 78. Assessment has to come before remediation, and one licensee cannot do both on the same project. Drying wet materials fast is the work that keeps mold from starting.
Key takeaways
- Texas licenses mold work through the Texas Department of Licensing and Regulation, under Chapter 78.
- Assessment must precede remediation, so the person who finds and measures the mold is not the person who removes it.
- One licensee cannot perform both the assessment and the remediation on the same project, which keeps the scope honest.
- Drying a wet structure is a different job from mold work, and a drying crew is not automatically a mold remediator.
- Mold needs moisture that lasts, so the readings taken during drying are the best early warning in a Waco house.
- Clay-soil slab leaks, crawl-space moisture and hail roof leaks each hold water in a different place, and each tends to show mold in a different place.
Who licenses mold work in Texas?
The Texas Department of Licensing and Regulation licenses mold assessors and remediators under Chapter 78. Work that is not exempt must be done by someone holding the right license.
The state treats mold as a licensed trade. The Texas Attorney General's consumer material and the department's own pages both describe the rule: non-exempt mold assessors and remediators must hold a license. The department is the agency to check, and it is the place to confirm that a person is licensed for the role you are hiring them to perform.
Notice what this does and does not say. It covers mold assessment and mold remediation. It is a different question whether any license applies to ordinary water damage restoration, such as pumping out water and running dryers, and this guide does not claim one. Ask any company what it holds and for what role, and verify the answer with the department. A person who says a license covers a job it does not cover has told you something worth knowing.
Why must assessment come before remediation?
Assessment defines what is there and how much, so the remediation scope rests on measurement and not on a sales pitch. Texas requires the assessment first.
An assessor looks at the building, takes readings and samples where appropriate, and writes a protocol: which areas, which materials, what should be removed and what clearance looks like at the end. That document is what a remediator then works from. Without it, a remediator is guessing at the extent, and a guess can run in either direction, too little removed or far too much.
This order also protects the reader. Because the assessment exists before the work begins, there is a standard to hold the work against. If the protocol says three wall bays and a section of subfloor, and the remediator removes a whole floor, you have a document to compare. If the protocol calls for a final check, you know the job is not finished until that check happens.
Why can one licensee not do both on the same project?
The separation keeps the person who decides how much mold there is apart from the person paid to remove it. Texas does not allow one licensee to hold both roles on the same project.
The rule is about conflict of interest. A firm that both diagnoses and treats has a reason to find more than is there. Splitting the roles gives you an independent opinion about the problem and a separate party doing the work, and the two check each other. It is the same logic as getting a second view before a major repair.
In practice that means you may deal with two parties for a mold project. That can feel like extra trouble when a house is already disrupted, but it is the structure the state set up. When you are comparing offers, a contractor who proposes to assess and remediate the same job is describing something the rule does not permit, and that is a reason to stop and verify. The guide on hiring a water damage contractor lists other questions to ask.
What causes mold after a wet event in a Waco house?
Mold needs organic material and moisture that stays. After a leak or flood, wet drywall, insulation, wood framing and carpet pad hold the water long enough for growth to start.
Water that is removed quickly and followed by thorough drying rarely leads to mold work. The trouble begins when moisture hides. A wall cavity behind a baseboard, the underside of a subfloor, a ceiling cavity under a leaking roof, or the space under a house on piers can stay damp for a long time, and mold takes advantage of that quiet. This is why a technician measures with a meter and opens small inspection holes instead of trusting how a surface looks.
Waco's mix of building ages adds variety. Older houses in neighborhoods such as Castle Heights and Sanger Heights have wood framing, plaster or old drywall, and sometimes crawl spaces, all of which have their own ways of holding water. Newer slab houses have different weak points, such as a leaking supply line in a wall or a slab edge that stays wet after a flood. The page on mold after water damage describes what that service involves.
How do Waco's soil and rain patterns affect mold risk?
The clay soils common in Central Texas swell and shrink with moisture, and slow ground drainage after heavy rain keeps moisture near foundations. Both extend the time materials stay damp.
McLennan County sits partly in the Grand Prairie and partly in the Blackland Prairie, with the Balcones Fault running through it from southwest to northeast. The eastern part has black, waxy clay and the western part has shallow, stony soils. Clay of this kind shrinks and swells with moisture, and the movement can crack pipes under a slab. A slow slab leak can wet the underside of flooring for a long time before anyone sees it.
Rain adds to this. May 2024 was reported as the wettest month on record in Waco, and the Corps releases water at the Lake Waco dam when the lake is too high. Weeks of wet ground keep moisture pressing toward foundations and crawl spaces. When the ground stays damp, so does the air in a crawl space, and wood framing and insulation up there can reach moisture levels that support growth without any plumbing leak at all.
What should happen first, before anyone talks about mold?
Stop the water, remove standing water and start drying. The aim is to bring wet materials back to normal moisture before growth starts.
Mold work is a second stage. The first is mitigation: shut off the source, extract, take out what cannot be saved and dry what can. Air movers and dehumidifiers do the drying, and meters confirm it. A crew that does this well often finishes without ever needing a mold protocol, because the conditions that support growth did not last. The page on structural drying and dehumidification explains the process.
Ask for the moisture readings. A written record of the starting readings, the readings during drying and the final readings is the best evidence that the structure came back to dry. If a reading stays high in a spot, that spot needs attention before it is closed up behind new drywall. Closing up a wet cavity is how a water event turns into a mold project months later.
What if I already see or smell mold?
Limit disturbance, keep the area closed off and arrange an assessment from a licensed assessor. Do not start tearing out large areas yourself, because that can spread material through the house.
Visible growth, a persistent musty smell or discoloration that returns after cleaning are all signs that moisture is still present. The first move is to find and fix the moisture, since cleaning mold without fixing the water only gives it a clean surface to return to. Turn off fans that would blow air across the area, and keep the space separate from the rest of the home where you can.
Then follow the state's order. Get an assessment from a licensed assessor, receive a written protocol, and only then hire a licensed remediator to carry it out. You can ask a restoration crew to dry the structure during this time, which is separate work. Keep photographs and the assessment, since they also help if you have an insurance claim, which the guide on water damage insurance claims explains in general terms.
How do you check that a license is real and covers the job?
Ask for the license holder's name and license type, then check it with the Texas Department of Licensing and Regulation. Confirm that the license matches the role: assessor or remediator.
Get the details in writing on the proposal. A mold assessor and a mold remediator hold different licenses, and the document should name which one is being offered. Look the person up with the department yourself instead of relying on a number printed on a flyer. If the name or role does not match, ask why.
Keep the order in mind and the roles separate. Your drying contractor can keep working while the assessment is arranged, and the assessor and remediator should be different parties on the same project. If you need to begin with water removal, a call to (833) 490-5225 reaches a line that is answered around the clock, and a crew is dispatched as fast as one is available. After that, follow the written protocol, not the loudest estimate.
Frequently asked questions
Does Texas require a license for mold work?
Yes. Non-exempt mold assessors and remediators must be licensed by the Texas Department of Licensing and Regulation under Chapter 78. You can check a person's status with the department. Make sure the license matches the role being offered, since assessor and remediator are different licenses.
Can the same company assess and remove the mold?
Not as the same licensee on the same project. Texas separates the two roles so the party that decides the scope is not the party paid to do the work. If a proposal offers both under one license, ask the department how that fits the rule before signing.
Does the same license cover drying out a flooded house?
This guide does not assert one. Mold assessment and remediation are licensed under Chapter 78, and drying a structure is a separate activity. Ask any company what it holds, for which role, and confirm it with the state. A drying crew should not present itself as a mold remediator unless it holds that license.
What is the best way to avoid mold after a leak?
Remove the water quickly, take out materials that cannot be saved and dry the structure until readings match normal. Ask for the written moisture readings. Do not close up walls or lay new flooring over anything still damp.
I smell mold but see nothing. What now?
A musty smell suggests moisture somewhere, often inside a wall cavity, under flooring or in a crawl space. A technician can use a moisture meter to find the damp area. If growth is found, the licensed path is an assessment first, then remediation by a separate licensed party.
Can I clean small mold myself?
Small amounts on hard surfaces are a household matter, but fixing the moisture is what stops its return. If the growth is extensive, hidden or keeps coming back, get an assessment. Avoid disturbing large areas yourself because it can spread material through the house.
Sources
This guide is general information for McLennan County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.