Phones answered 24/7Waco, TX
Call (833) 490-5225
(833) 490-5225
Guide

What to Check in a Waco Home After a Flash Flood

After fast water recedes from a Waco home, check the floors, the wall cavities and the furnace area in that order. Here is what each check looks for and why.

Illustration for the guide "What to Check in a Waco Home After a Flash Flood" (Waco, TX)
Short answer

After fast water recedes, check three places: the floor and what sits under it, the wall cavities behind the baseboard, and the furnace and water heater area. Water that moved quickly leaves silt and contamination behind, and it often travels into spaces you cannot see.

Key takeaways

  • A flash flood in Waco can drop a large amount of rain on the US-84 and I-35 corridor in a short time, and the water may be gone before the damage is understood.
  • Floodwater carries silt and whatever it passed through, so it is treated differently from a clean supply-line leak.
  • Flooring is checked first because the subfloor, pad and underlayment hold water long after the surface looks dry.
  • Wall cavities behind the baseboard can stay wet for a long time, since insulation soaks up water and releases it slowly.
  • The furnace area and the water heater sit low and hold ignition, wiring and controls that water can ruin, so they are not restarted until they have been inspected.
  • Heavy rain here may arrive in one short burst, which is why the first look at the damage is part of the work and not the end of it.

Why does a quick flood leave so much behind?

Fast water carries mud, silt and debris, and it pushes into gaps at speed. When it recedes, the surfaces look wet but the real problem is what the water left and where it went.

The National Weather Service office in Fort Worth has issued flash-flood warnings that cover the US-84 and I-35 corridor between Bellmead and Hewitt, which includes the Waco metro. One of those warnings said two to four inches of rain in an hour was possible. That is the kind of rate where ditches, low yards and street drains stop keeping up, and where water can cross a threshold in minutes and be back out in the street within hours.

The speed is the trap. A homeowner comes back to find a thin film of silt on a floor that is already draining and concludes it was a small event. Meanwhile water has soaked into the slab edge, the bottom plate of the walls, the cabinet toe kicks and the insulation. What matters is how far the water reached into materials, and a squeegee does not answer that. A systematic check does, and it begins at the floor.

What do you check on the floors first?

Check the surface, the pad or underlayment and the subfloor or slab edge. Floors absorb water downward and sideways, so the visible layer is the least reliable guide.

Lift a corner of carpet at a wall and feel the pad. Pad acts like a sponge, and it holds water against the tack strip and the lower wall long after the carpet surface feels firm. On a laminate or engineered wood floor, look for cupping or gaps opening at the seams, which show that the planks have taken up water from below. Tile can seem untouched while the mortar bed and subfloor under it stay wet.

On a slab-on-grade house the slab does not swell, but it does hold moisture, and anything laid on it traps that moisture against the slab. In a pier-and-beam house the question moves below the floor to the crawl space, where standing water, damp insulation and wet soil can put moisture into the floor framing from beneath. Both layouts appear in Waco's older neighborhoods, and the page on pier-and-beam crawl space moisture explains what a technician looks for there.

What about the wall cavities?

Look behind the baseboard and at the bottom of the drywall. Water wicks upward into drywall and sits against insulation inside the cavity, where it can stay wet for a long time without any sign on the outside.

Drywall pulls moisture upward like a wick, so a wall that stood in an inch of water can be wet well above that mark. Press along the lower wall for softness, look for a darkened line, and notice any musty smell. A technician checks with a moisture meter and often drills or cuts a small inspection opening at the base to see inside the cavity without guessing.

Insulation is the part owners forget. Batts hold water and release it slowly into the framing, and they keep the cavity damp enough for mold to start. Floodwater is not clean water, so insulation that has been soaked in it is usually removed, not dried in place. See ceiling and drywall water damage for how cuts and removals are made and what stays in place. Photograph the cavities before and after, because that record matters if an insurer needs to see the extent.

Why are the furnace and water heater areas on the list?

They sit low in the house and contain controls, wiring and ignition parts that water damages. Do not restart a furnace or water heater that has been wet until it has been inspected.

Many Texas homes put the furnace and water heater in a closet, a garage corner or the attic, and each of those spots has a different exposure. A garage or utility closet takes water first. Ignition modules, gas controls and electrical connections that were submerged can fail in ways that do not show until the unit is powered up. Treat anything that was wet as suspect and keep it off until a qualified tradesperson has examined it.

The ductwork matters too. Supply and return ducts that run through a slab or low in a closet can take on water and silt, and the air handler can then spread dust and contamination through the house. Check the filter and the area around the return, and keep the system off while the house is being dried. For a water heater that leaked or was flooded, the guide on water heater leak damage describes the moisture patterns that follow.

Is it safe to touch the water and the materials?

Treat floodwater as contaminated. Wear boots and gloves, keep children and pets out, and have electrical circuits that were wet checked before using them.

Surface water from a storm picks up what it crosses: yards, drains, driveways and sometimes a sewer line that has backed up. The water that entered the house should be assumed to carry contamination, and materials that soaked in it are handled with care. Porous items such as carpet, pad, insulation and particleboard cabinetry are the first to be discarded. Hard, sealed surfaces can often be cleaned and dried.

If the water came up through a floor drain or a toilet, it was a sewer event as well as a flood, and the cleanup follows sewer backup cleanup. In either case, outlets and cords that were under water should not be used until checked, and a breaker panel that sits low should be treated cautiously. Mud on a floor is not only dirt; it holds moisture against the surface and adds a biological load, so removal is part of drying.

How does Waco's ground and river history change the picture?

The Brazos, the Bosque and Tehuacana Creek shaped Waco, and the clay soils common in Central Texas drain slowly. Low ground and slow soil mean water can stand for a while after the rain stops.

The Bosque meets the Brazos at the top of Cameron Park, and Tehuacana Creek joins the Brazos about a mile east of town. The floods of 1913 and September 1936 hit East Waco hardest, and the April 1957 flood led to the dam that now holds Lake Waco. Those events are why many longtime residents already know which low places take water. A flash flood is a different mechanism from a river flood, though, because it comes from rain falling on the city itself, and it can reach neighborhoods that never touched the river.

Clay soil adds to the problem. When clay is wet it takes in little more water, and runoff has nowhere to go but downhill. After the rain, soil along the foundation can stay saturated for days, pushing moisture toward the slab edge and the crawl space vents. Check the perimeter of the house, see where water stood, and note the line it left on exterior walls or fence boards. A high-water mark is useful evidence for a technician and for an insurer.

How should the checks be recorded?

Record the damage with dated photographs and notes by room, starting before anything is moved. Separate flood damage from any plumbing or roof damage from the same storm.

Work room by room. In each one, take a wide shot, then photograph the floor, the base of the walls, the cabinets and any appliance that sat in the water. Write down the high-water mark where you can see it. Keep damaged items until they are photographed, and keep a rough list of contents. If an appliance or heater was wet, note it and leave it off.

The point of the record is to support two things: a drying plan and a claim. Flood is generally not covered by a home policy, and a separate flood policy handles it, while a roof leak or burst pipe in the same storm falls under the home policy. The guide on water damage insurance claims explains that split. Tell the technician which parts of the damage came from outside water and which came from inside so the notes are clear.

When does the drying start, and what does a crew do?

Drying starts as soon as the standing water is out and the materials that cannot be saved are removed. A crew extracts water, removes wet materials and runs air movers and dehumidifiers until readings come down.

Extraction comes first, using pumps and wet vacuums to take off standing water and pull it from carpet and pad. Then the wet materials that cannot be saved come out: pad, lower drywall, wet insulation, swollen baseboard. The framing and the slab are left to dry with air movement and dehumidification. See flood water extraction and pumping for how that stage is done.

Readings guide the end of the job. The crew measures the moisture in the framing and subfloor at the start, and again as the equipment runs, until those numbers match dry reference materials in the same house. Calling (833) 490-5225 reaches an answered line at any hour, and a crew is dispatched as fast as one is available. Do not rely on a floor that looks dry, because the cavity behind it is the part that decides whether mold comes later.

Frequently asked questions

How do I know if water got into my walls after a flash flood?

Press along the base of the drywall for softness, look for a stain line, and notice a musty smell. A technician uses a moisture meter and often opens a small inspection hole at the base to look inside the cavity. Drywall wicks water upward, so the wet area is usually higher than the visible mark.

Can I run my furnace after the house flooded?

Not until it has been inspected. A furnace or water heater that was wet may have damaged ignition parts, gas controls and wiring that fail when powered. Keep the unit off, keep the system off while the house is dried, and have a qualified tradesperson examine it.

Is floodwater different from water from a broken pipe?

Yes. Floodwater carries silt and whatever it crossed, so porous materials that soaked in it are usually removed instead of dried in place. Water from a clean supply line is treated more gently. Sewer backup is handled as a third case with its own precautions.

Why does the floor feel dry when the house was flooded?

The surface dries first while the pad, underlayment, subfloor and slab edge hold water longer. Lift a corner of carpet to feel the pad, and look for cupping on wood or laminate. Moisture readings tell you what is left under the surface.

What if the water came from the Brazos or a creek and not from rain on the house?

The cleanup steps are similar, but the insurance treatment differs because river or creek water entering a building is flood. A home policy generally does not cover flood, and a separate flood policy handles it. Record where the water entered and how high it rose so the claim can be sorted correctly.

How long should I wait before calling for help?

Do not wait for the water to look gone. Moisture keeps working inside the walls and the floor, and the longer materials stay wet the more of them have to be replaced. Shut off power to wet circuits, photograph the damage and get extraction and drying started.

Sources

  1. Texas Water Development Board
  2. Texas Department of Insurance

This guide is general information for McLennan County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.

Need help today?

Call any hour and explain what is going on. You get a clear price before any work starts.

Keep reading

More guides

WhatsApp